Arduino MKR WAN 1310 - LoRaWAN SAMD21 - ABX00029
- Артикул:
- 42762814
Характеристики
- UC - I2C
- yes
- UC - USB
- microUSB
- UC - A/C
- 12-bit
- UC - C/A
- 1
- UC - PWM
- 12
- UC - UART
- yes
- UC - ядро
- 1. Single Core, 32-bit ARM Cortex M0
- UC - Разъем
- 5V microUSB
- UC - Вспышка
- 256 kB
- Напряжение до
- 5.0 V
- Напряжение от
- 6.0 V
- Интерфейс UC - SPI
- yes
- Выходное напряжение от
- 5.0 V
- Выходное напряжение до
- 5.0 V
- UC - оперативная память
- 32 kB
Общие характеристики
- UC - частота
- 48 MHz
- UC - аналог в
- 7
- UC - Микроконтроллер
- SAMD21
- UC - Цифровые контакты
- 8
Производительность
- Тип
- Запчасть для микрокомпьютера
Прочие свойства
- EAN
- 7630049201484
- Бренд
- Arduino
Энергопитание
- Номинальное выходное напряжение
- 5.0 V
Описание
Module with32-bitAtmel ARM Cortex-M0+microcontroller, 256 kB Flash memory and 32 kB SRAM. The board can be connected to:ArduinoCreateplatform,LoRa's ownLoRa network using Arduino Pro GatewayLoRa, as wellas existing LoRa WAN infrastructure such as The Things Network.MKR WAN 1310has a new battery charging circuit, 2 MB of flash memory and improved control of power consumption by the board.I/O pins work with 3.3V,higher ones candamage the board. The module is fully compatible with Arduino environment.
The subject of sale is original Arduino product, Botlandis an officialdistributor of this company.
For communication with LoRa network, the module uses MurataCMWX1ZZZABZchip,so you can create various projects requiring wireless communicationor projects based on IoT(Internet of Things).Arduino MKR WAN 1310 is powered by the built-in microUSB port with 5 V or byLi-Ion or Li-Pol 3.7 Vbatteries.The module consumes only104 uA ofcurrent. MKR WAN 1310 thanks to 2 MB flash memory supports data logging and OTA (Over The Air). These functions allow you to transfer configuration files to the board, create your own scripting commands or simply store local data and transfer it to another location.
Main featuresBelow we present several features that distinguish MKR WAN 1310 fromotherprogrammable tiles.
Feature DescriptionInstalled
bootloader
Thanks to the installed bootloader, the appropriatemicroUSB cable andsoftware from themanufactureris sufficient to program the device.Small
size
This version has a small size: 67.64 x 25 mm. It has soldered-in male connectors on the bottom and female connectors on the top.Downloads
digital
8 digital inputs/outputs enable, among other things, control of LEDs, relays and readout of button states.Performance
Current
The maximum current capacity of a single output is 7 mA.Outputs
PWM
12 PWM outputs allow e.g. for motor control and LED brightness adjustment.Inputs
analogue
7 inputs of the built-in analog-to-digital converter with a resolution of up to 12 bits support, among others, sensors with analog output.Communication
serial
The device supports popular communication interfaces, among others: UART, I2C and SPI.Memory
Embedded
AtmelSAMD21chip isclockedwith 48 MHz signal, has 256 kB of flash memory and 32 kB of SRAM. Additionally, the board has 2 MB of external flash memory (QSPI).Power supply 5 V
microUSB / 3.7 V battery
To power Arduino you can use 5V power supplywithmicroUSB connector, VIN pin with 5 to 6V or 2 AA/AAA rechargeable batteries. It is also possible to connect Li-Ion or Li-Pol rechargeable battery via JST PHR-2 connector.LoRa
Radio communication with low power consumption and relatively long range, ideal for IoT devicesPlaying music files
The module allows you to play music files via the SPI interface (SPI1).First start-up
In order to make it easier to start working with the module, we have prepared a guidethatcovers the installation and first start-up of Arduino environment.
Specification of Arduino MKR WAN 1310 module- Processor: Atmel SAMD21 ARM Cortex-M0+ 32 bits
- Clock: 32.768 kHz (RTC), 48 MHz
- Power supply voltage (USB/VIN): 5 V
- Battery power: 2x AA or 2x AAA / Li-Ion or Li-Pol battery
- Operating voltage of I/O pins: 3.3 V
- Digital I/O pins: 8
- PWM pins: 12
- Interfaces supported: UART, SPI, I2C
- Analogue input pins: 7 (ADC 8/10/12 bit)
- Analogue output pins: 1 (DAC 10 bit)
- Pins supporting external interruptions: 8
- Maximum current of I/O pins: 7 mA
- Flash memory: 256 KB
- SRAM: 32 KB
- External flash memory: 2 MB
- Built-in LEDs: 6
- Connectors: microUSB, micro uFL, JST PHR-2
- Maximum antenna power: 2 dB
- Frequency of operation: 433/868/915 MHz
- Dimensions: 67 x 64 x 25 mm
- Weight: 32 g
Arduino MKR WAN 1310 - top view.
In case of installing software downloaded from a source module other than the one described on the back of the module, the user will receive a message about an unauthorized PCB supplier. You can cancel it with one click and the environment will work properly.
We assure you that all tiles marked with Arduino symbol are original and come from one source - you can check the list of authorizedvendorsto see it.
Useful links- Installation and first start-up
- Arduino Forum
- Arduino IDE software
- Module diagram
- Eagle files
- Fritzing files
