GSM LTE Module IoT-u-GSM shield v2.19 BC95G - for Arduino and Raspberry Pi - u.FL connector
- Артикул:
- 42766477
Характеристики
Дизайн
- Тип
- Запчасть для микрокомпьютера
Производительность
- Тип
- GSM модуль
Прочие свойства
- EAN
- 5904422320508
- Бренд
- Itbrain Power
Описание
The module is working withArduino,Raspberry Pi (version 3B+, 3B, 2B, B+ and A+)andthe BeagleBone Black, which enables communication in the standard of GSM, LTE. It allows for the voice chats, sending SMS messages. On the board are: connector forSIM card, powering module for battery LiPol / Li-Ionandthe RESET button. It has a connector of theu.FLantennasfor GSM.
The distribution of elements on the u-uGSM shield board.
Specification
- Driver: Quectel BC95G
- Supported standards: GSM / LTE / NB-IoT
- LTE: B1 / B2 / B3 / B5 / B8 / B20 / B28
- The speeds of the NB-IoT Single tone / Multi tone: max. 25.2 Kb/s (DL), max. 15,625 / 54 Kb/s (UL)
- Nano SIM / micro SIM connector
- The u.FL antennas connectors
- Built-in USB to UART converter (USB connector can be used to power the module)
- Automatic selection of logic levels between 3 V to 5 V
- The Reset button
- It works withArduino,Raspberry PiandBeagleBone Black along with sample codes of the manufacturer
- Two mounting holes with a diameter: 2.5 mm
- Board sizes: 45 x 27 mm
Detailed module description can be found in the user guide in the firstandsecondpart, and onthe website of the manufacturer.
Pins
Pin Description STS The status output. RI The Output Ring Indicator. GND The ground of the system. VCC Input/output of 4 V, internally connected to a Li-Pol + pad. VIN 5 V Input for Li-Pol charger. VUSB The 5 V output. ENA The activation pin is activated by the high status. RST Reset is activated by the high status. TX Communication is via the serial interface. RX Communication is via the serial interface. The connection to the Arduino
The system works with Arduino Uno using the following pins:
Pin Arduino Description GSM RX D3 Communication via the serial interface. GSM TX D2 Communication via the serial interface. RESET D6 System reset of GSM. Ena D7 The supply voltage control of the GSM system (On/Off). VIN (5 V LiPol) 5 V
Power supply of 5 V. Details of the connection, in case of LiPol battery, are available inthe manufacturer's manual.
GND
GND The ground of the system.STATUS
D5 The status pin.Connection to the Raspberry Pi
The module has special, breakable connectors that allow you to connect directly attached to the GPIO connectors of the Raspberry Pi or BeagleBone Black.
To start the module with the Raspberry Pi, you must perform the following connections:
Pin RPi Description GSM RX 10
Communication via the serial interface (not connected in the USB communication).
GSM TX 08Communication via the serial interface (not connected in the USB communication).
RESET 18 GSM system reset. ON / OFF 16 The supply voltage control of the GSM system (On/Off). VIN (5 V LiPol) 02/04 The supply voltage of 5 V.GND
04/14 The ground of the system. STATUS 12 The status pin.Useful links
- The manufacturer's website
- User manual 1
- User manual 2 - connection to the Raspberry Pi
- User guide 3 - connecting with the BeagleBone Black
- Presentation of the u-GSM modules
- Documentation of the Quectel BC95G module