Характеристики
- Напряжение до
- 220 V AC
- Напряжение от
- 240 V AC
Общие характеристики
- Паяльник - Вентилятор
- yes
- Припой - Горячий воздух
- yes
- Кондиционер паяного типа
- Цифровой
- Припой - показания реальной температуры
- yes
Прочие свойства
- Бренд
- YIHUA
Свойства
- Температура
- 200 - 480 °C
Энергопитание
- Номинальная мощность
- 720 W
- Номинальное напряжение
- 230 V AC
Описание
Description: 2in1 hotair and Yuihua 995D main soldering station with fan in the flask - 750 W
Soldering station equipped with amainsheet andhotair flask. The total power of the station is 750 W. It is equipped with a PID controller, LCD display and a hotair flask with a fan. The flask is made in ESD Safe technology. The power of the mainsheet flask is 50 W. The maximum hot air flow is 120 l/min.
Soldering station Yihua 995D.
Check our offer of additional blades!
Compatible T-x series blades.
Soldering station heat-up characteristicsZhaoxin and Yihua soldering stations heat up very similarly.Yihua heats up much faster. This difference ensures that you can work at lower / safer temperatures, because the station will quickly compensate for heat loss. The measurements were taken on an external sensor at the end of the G-3C mainsail.
Heat-up time diagram.
Main features of the Yihua 995D soldering station- 2-in-1 station - mainsail and hotair.
- High quality heating elements.
- Hotair flask can work in automatic or manual mode. In automatic mode, when the flask is put away, the station starts to cool down, and when the heater reaches safe temperature, the air supply is also switched off.
- Sleep mode of the main flask when it is not used with a set time from 1 to 99 minutes.
- Digital calibration of the temperature in °C and °F.
- PID controller.
- Large LCD display.
- Flask made with ESD Safe technology.
- Compact housing.
- Fan integrated in the flask.
- Supply voltage: 220 V to 240 V AC
- Power consumption: 750 W
- Operating temperature: 0°C to 50°C
- Storage temperature: from -20°C to 80°C
- Station dimensions: 260 x 165 x 148 mm
- Hotair soldering iron:
- Supply air source: fan
- Maximum airflow: 120 l/min.
- Operating temperature: from 100°C to 480°C
- Temperature stability: +/- 1°C
- Display type: LCD
- Cable length: 90 cm
- The main soldering iron:
- Power: 50 W
- Operating temperature: 200°C to 480°C
- Temperature stability: +/- 1°C
- Display type: LCD
- Cable length: 90 cm
- Potential between mainsail and ground: up to 2 mV
- Resistance between mainsail and ground: up to 2 Ω
- Flask: 907L
- Security: ESD Safe
- Yihua 995D station
- Hotair flask tray
- A set of nozzles:
- round with a diameter of 4.4 mm
- round with a diameter of 8 mm
- round with a diameter of 9 mm
- square 12 x 12 mm
- Main flask holder with cleaning sponge
- Mainsail with mainsail T-I
- System lift gripper
- Power cord
- Manual
First start-up
- Do not start it up immediately after the equipment is delivered.
- The equipment should remain at room temperature for approximately 12 hours before start-up.
- Any reports of faults caused by premature start-up will be rejected.
- Completely remove the screw(s) from the bottom of the station if the source of supply is a compressor. These screws are marked in red (1 or 3 screws depending on model).
- Soldering binders - tin with different diameters
- Fluxes and rosin
- Braids for removing excess tin
- Suction units
- Soldering caves
- The tweezers,handles, magnifiers
- Sponges and cleansers