Core429I module - STM32F4 ARM Cortex M4 - Waveshare 9116

Бестселлер
47769500
-25%
42 258 AMD
Старая цена 56 186 AMD
  • Бренд waveshare
  • Доставка из Польши
  • Курьер DHL 2 июня
  • Стоимость доставки заказа в Армению от 72 145 AMD

Сроки доставки указаны ориентировочно и зависят от региона доставки. Подробнее на этой странице

Характеристики

Прочие свойства

Бренд
waveshare

Описание

Description

Module with 32-bit microcontroller with ARM Cortex M4, 180 MHz, 1 MB Flash, 256 kB SRAM. In addition, the board has a 64 MB SRAM. Based on the system STM32F429IGT6. It allows to get acquainted with the system STM32F.

 

 

Specification
  • Processor STM32F429IGT6:
    • Frequency: 180 MHz
    • Supply voltage: from 1.8 V to 3.6 V
    • Flash memory: 1024 KB
    • SRAM: 256 KB
    • Communication interfaces:
      • 6 x SPI
      • 4 x USART
      • 4 x UART
      • 2 x I2S
      • 3 x I2C
      • 1 x SAI
      • 1 x FMC
      • 1 x sdio format
      • 2 x CAN
      • 1 x LCD display TFT
      • 1 x USB 2.0 HS / FS(with dedicated DMA)
      • 1 x USB HS ULPI (external PHY is needed)
      • 1 x Ethernet 10 / 100
      • 1 x camera interface-8 to 14 bits
    • 3 x inverter A/C: 12-bit
    • 2 x Converter for C/A: 12-bit
    • Debugging / programming: supports interface, JTAG / SWD, IAP support
  • In addition, on the board there is memory 64 Mbits SRAM
  • Reset Button
  • miniUSB port (included USB cable - miniUSB)
  • Raster: 2 mm
  • Dimensions: 83 x 57,50 mm

Detailed materials can be found inthe user guide.

 

What is on the board?
  1. Processor STM32F429IGT6
  2. IS42S16400J: SDRAM, 1 MB x 16 b x 4 banks (64 Mb)
  3. AMS1117-3.3: voltage regulator 3.3 V
  4. MIC2075: built-in power management USB
  5. Power switch: USB or 5VIN contact
  6. Selection of loading mode: for configuring the BOOT0 contact
  7. LED indicating the power
  8. LED VBUS
  9. RESET button
  10. Quartz resonator 8 MHz
  11. Quartz resonator 32.768 kHz for internal RTC with calibration
  12. Interface JTAG / SWD for debugging and programming
  13. MiniUSB connector
  14. Removed pins CPU
  15. Pin-5VIN: power supply is required when using USB HOST/OTG
  16. Jumper USB HOST/OTG
  • Closed: using USB HOST/OTG
  • Open: disconnecting from I/O ports
VBAT jumper
  • Closed: use of system power
  • Open: connect the VBAT to external power,such as battery
VREF jumper
  • Closed: connect VREF+ to VCC
  • Open: connect VREF+ to the other pins via optional cable

 

Useful links
  • The website of the manufacturer: Waveshare
  • User guide Wiki
  • Sample program
  • Diagram of the module