Характеристики
- UC - I2C
- yes
- UC - UART
- yes
- UC - ядро
- 1. Single Core, Cortex M4
- UC - Разъем
- 5V microUSB
- Напряжение от
- 3.3 V
- UC - аналог в
- 8
- UC - Bluetooth
- yes
- Интерфейс UC - SPI
- yes
- Выходное напряжение до
- 3.3 V
- UC - Цифровые контакты
- 14
Общие характеристики
- UC - Вспышка
- 1 MB
- UC - частота
- 64 MHz
- UC - Микроконтроллер
- nRF52840
- UC - оперативная память
- 256 kB
Прочие свойства
- EAN
- 7630049203488
- Бренд
- Arduino
Описание
The task of the Arduino Nano series modules is to extend the possibilities of small boards in order to use them in any project. Arduino Nano 33 BLE Sense Rev2 is equipped with an energy-saving and efficient nRF52480 microcontroller that can work with a clock speed of up to 64 MHz . On its board there is space for 1 MB of Flash memory and 256 kB of RAM. Thanks to the use of this unit, the Nano 33 BLE Sense Rev2 board is the most energy-efficient representative of the Nano family. In addition, the board is equipped with a number of sensors, giving a lot of possibilities. It supports Bluetooth 5.0 Low Energy communication.
The offered board has leads for self-assembly. We also offer a version with connectors .
Arduino Nano 33 BLE Sense Rev2.
Arduino Nano 33 BLE Sense Rev2 managing Bluetooth communication in the 5.0 LE standard.
Arduino Nano 33 BLE Sense is equipped with the U-blox NINA B306 module that manages Bluetooth communication in the 5.0 LE standard . On board Nano there are two IMU (Inertial Measurement Unit) - 6-axis BMI270 and 3-axis BMM150 communicating via the I2C bus, which includes a 3-axis gyroscope, accelerometer and magnetometer. In addition, the small size of the board is equipped with a temperature and pressure sensor LPS22HB , a humidity sensor HS3003, a sensor of light intensity, colors and gestures ADPS-9960 . There was also room for the MP34DT05 digital microphone . In addition, the ATECC608A cryptographic chip was also on board.
Arduino Nano 33 BLE Sense only works with 3.3 V by default . In the place of the 5 V pin on the standard Nano board (between the RST and A7 pins), there is a jumper that can be shorted to USB power. To power the devices with 5 V, solder the jumper and power the Nano via USB . If the jumper is soldered and the power is taken from the VIN pin, no voltage will be obtained. This is a protection designed to protect the Arduino Nano 33 BLE Sense.
Attention!
Arduino Nano 33 BLE Sense can only work with 3.3 V by default. Do not power it directly with 5 V.
Arduino Nano 33 BLE Sense pins. Visible jumper for 5 V power supply via USB.
Kit contents.
- Supply voltage: 3.3V
- Microcontroller: nRF 52840
- Clock: 64MHz
- Flash memory: 1MB
- RAM memory 256 kB
- Digital pins: 14
- PWM pins: 6
- Analog pins: 8
- microUSB socket
- Interfaces: GPIO, SPI, I2C, USART, PWM
- Converters: ADC, DAC
- Dimensions: 45x18mm
- Arduino Nano 33 BLE Sense Rev2 - ABX00069
- A set of goldpin connectors
(*) Unlike the standard Arduino Nano, pins A4 and A5 have default pull-ups. pull-up and are used as an I2C bus, so it is not recommended to use them as analog inputs.
- Manufacturer's website
- Arduino forums
- Installation and first run
- Arduino IDE software
- nRF 52840 documentation
- NINA B306 documentation
- LPS22HB documentation
- ADPS-9960 documentation
- MP34DT05 documentation